ITEM |
UNIT |
VT-23 |
VT-23M |
VT-23MS |
VT-23S |
| CAPACITY | |||||
| Swing over Z way cover | mm | 620 | 620 | 620 | 620 |
| Max. turning diameter | mm | 370 | 370 | 370 | 370 |
| Swing over cross slide | mm | 400 | 400 | 400 | 400 |
| Distance between centers | mm | 650 | 650 | 650 | 650 |
| Slideway slant angle | degree | 45 | 45 | 45 | 45 |
| TRAVEL | |||||
| X-axis travel | mm | 185+40 | 185+40 | 185+40 | 185+40 |
| Z-axis travel | mm | 700 | 700 | 700 | 700 |
| W-axis travel | mm | - | - | 650 | 650 |
| SPINDLE | |||||
| Type of spindle nose | ISO | A2-8 | A2-8 | A2-8 | A2-8 |
| Main spindle through capacity | mm | 7 5 | 7 5 | 75 | 75 |
| Main chuck type | mm | 1 0" | 1 0" | 1 0" | 1 0" |
| Main spindle through bar capacity | mm | 6 5 | 6 5 | 65 | 65 |
| Main spindle RPM | 4 500 | 4 500 | 4 500 | 4 500 | |
| Main spindle drive motor(cont/30min) | HP | 3 5 | 3 5 | 3 5 | 3 5 |
| Sub. chuck type | mm | - | - | 6 " | 6 " |
| Sub. spindle drive motor(cont/30min) | HP | - | - | 7.5/10 | 7.5/10 |
| Sub. spindle RPM | - | - | 5000 | 5 000 | |
| Sub. spindle through bar capacity | mm | - | - | ∮42 | O∮42 |
| TURRET | |||||
| Toolholder type | - | V DI40 | V DI40 | - | |
| Shank height of square tool | mm | - | 25 | 25 | - |
| Shank diameter for boring bar | mm | - | ∮40 | O∮40 | - |
| Torque | NM | - | 22 | 22 | - |
| AXIS | |||||
| RAPID (X/Z/W) | M/min. | 18/24/24 | 18/24/24 | 18/24/24 | 18/24/24 |
| Ballscrew diameter of x-axis | mm | ∮3 2 xP 8 | ∮3 2 xP 8 | ∮3 2 xP 8 | ∮ 32 xP 8 |
| Ballscrew diameter of z-axis | mm | ∮3 6 xP10 | ∮3 6 xP10 | ∮3 6 xP10 | ∮ 36 xP10 |
| Ballscrew diameter of w-axis | mm | - | - | ∮ 40 xP10 | ∮ 40 xP10 |
| TAILSTOCK | |||||
| Tailstock spindle diameter | mm | 85 | 85 | - | - |
| Tailstock spindle travel | mm | 80 | 80 | - | - |
| Taper hole of tailstock spindle | MT4 | MT4 | - | - | |
| REMARKS | |||||
| Floor space | mm | ||||
| Machine weight (appro.) | kg | 5 100 | 5 200 | 5300 | 5200 |